Prescolite IBX26ICATDM User Manual download pdf

WARNING: When using special control devices with this ﬁxture, follow instructions carefully to ensure N.E.C. compliance. For

more help, contact a qualiﬁed electrical contractor. To prevent electrical shock, turn off electricity at fuse box before installing or

servicing this product.

WARNING: Thermal insulation may be installed in direct contact with ﬁxture, but DO NOT install insulation in excess of eight

inches deep above ﬁxture. Greater depth may cause the internally protected ballast to cycle the ﬁxture on and off.

CAUTION: To complete the installation, choose only UL listed Prescolite trims from the label (3) inside the housing (2). The use of

any trim not listed in this ﬁxture is a violation of N.E.C. article 110-3(B) and voids all warranties.

NOTE: This ﬁxture comes with replaceable ballast (25). Should the ballast fail; contact a qualiﬁed electrician to replace it. If further

assistance is required, contact: Warranty Services at: (864)678-1000.

1. For joist installation: Use the centering notches (4) located on the plaster frame (14) to position the ﬁxture. Extend the hanger

bars (5) and position the alignment tabs (6) underneath the support joist (7) (Fig.2). Drive the afﬁxed fastener (8) into the support

joist (7) to secure the housing. Drive additional fasteners through holes in hanger bars (9) for alternate support as needed (Fig.2).

2. For suspended ceilings: Using a ﬂat head screwdriver or other tool, bend the integral t-bar mounting tabs (10) downward to a

vertical position (Fig.3). Position the housing over the inverted t-bar (26) (Fig.4). Secure housing to support structure with tie wire

(supplied by others) in the holes supplied (9). Secure the housing to the inverted t-bar with sheetmetal screws (supplied by others) in

the holes supplied (12).

3. Locate housing along hanger bar in desired position and, using pliers, squeeze the 4 locking tabs (13) on the plaster frame

(14) tightly over the bars to prevent further housing movement (Fig.4). Bar hangers (5) may be installed in alternate slots (15) if

perpendicular orientation is desired.

4. As desired, hanger bars (5) may be shortened to ﬁt in narrow joist spacings by breaking at the score lines (26) provided (Fig. 5).

5. Unsnap junction box cover (16) by lifting the leaf spring (17).

6. Run supply wires through UL listed connectors (supplied by others) in one of the ﬁve pryouts (18) on the junction box (19) or type

NM cable (ROMEX) through an opening above the wire retaining plate (20). Connect wires (21) as shown in Fig. 8. Replace cover

(16).

7. FOR AIR-TIGHT APPLICATIONS: This Prescolite product is Air-Tight approved per ASTM E283 testing standards and complies

with Washington State Energy Code requirements. To complete the installation of this Air-Tight product, the opening between the

ceiling (24) and housing edge (27) must be sealed by the installer using silicone caulking, tape, or any other means acceptable to

the local code ofﬁcial. Prescolite accessory gasket kit G6 (purchased separately) can be used for this purpose (See Fig. 6).

8. Select a trim from the wattage label inside the housing. Use only lamp types and wattages approved for the trim chosen.

DO NOT EXCEED MAXIMUM LISTED WATTAGES!

9. Loosen wingnut (22) to adjust housing (2) for variations in ceiling media thickness.

This instruction sheet is intended for use as a Paint Shield. Upon completion of installation,

crumple this sheet up and insert it in the housing to protect the wattage label from paint spray.

INTRUCTION SHEET MUST BE REMOVED FROM FIXTURE PRIOR TO ENERGIZING.

InstructionSheet

Part No........................................................93010068

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed

by qualiﬁed service personnel. Product must be grounded to avoid potential electric shock or other

potential hazard. Product must be mounted in locations and at heights and in a manner consistent with

its intended use, and in compliance with the National Electrical Code and local building codes. The use

of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe

condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow

items such as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as

this may cause an unsafe condition.

INSTALLATION INSTRUCTIONS

IBX26ICAT/IBX26ICATDM

www.prescolite.com Prescolite TollFree Technical Support 1.888.PRS.4TEC Hours: 8am - 5pm ET

701 Millennium Blvd. • Greenville, SC 29607

With representatives ofﬁces in principal cities throughout North America.

1 2

InstructionSheet 1
WHITE SUPPLY 2

Summary of Contents

Page 1 - InstructionSheet

WARNING: When using special control devices with this ﬁxture, follow instructions carefully to ensure N.E.C. compliance. For more help, contact a qu

Page 2 - WHITE SUPPLY

InstructionSheetPart No..............93010068www.prescolite.com Prescolite TollFree Technical Support

Related models: IBX26ICAT

Comments to this Manuals

No comments

Prescolite IBX26ICATDM User Manual

Browse online or download User Manual for Lighting Prescolite IBX26ICATDM. Prescolite IBX26ICATDM User Manual

Summary of Contents

Related models: IBX26ICAT

Comments to this Manuals

Related products and manuals for Lighting Prescolite IBX26ICATDM