Prescolite BX4-12 User Manual download pdf

Instruction

Sheet

Part No...........................................

With representatives offices in principal cities throughout North America.

701 Millennium Blvd., Greenville, SC 29607

www.prescolite.com



Prescolite Toll Free Technical Support

1.888.PRS.4TEC



Hours: 8am - 5pm ET

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install i

n areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker.

All servicing or relamping must be performed by

qualified service personnel. Product must be grounde

d to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory e

quipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains

, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

93010070

Sheet 1 of 2

2012 09/25/12

INSTALLATION INSTRUCTIONS

BX4-12

WARNING: When using special control devices with this fixture, follow instructions carefully to ensure N.E.C.

compliance. For more help, contact a qualified electrical contractor.

WARNING: This product contains chemicals

known to the State of California to cause cancer, birth defects

and/or other reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise

touching this product.

CAUTION: RISK OF FIRE: Recessed portions of recessed housi

ng, other than at points of support, shall be

spaced at least ½ inch from combustible material. Thermal insulation shall not be installed within 3 inches of

recessed housing or junction box, and shall not be installed above fixture as to entrap heat and pr

event the

free circulation of air.

CAUTION: To complete the installation, choose only UL listed Prescolite trims from the label inside the

housing. The use of any trim not listed in this fixture is a violation of N.E.C. article 110-3(B) and voids all

warr

anties.

1. For Wooden Joists: Use the Centering Notches (4) located on the Plaster Frame to position the Fixture.

Extend the Bar Hangers (6), use joist alignment tabs to locate fixture and hammer the 4 Nails (7) into Joists (8)

(Fig. 1). Drive additional nails through holes in Bar Hanger for alternate support if required.

2. For Suspended Ceilings: Place the Fixture on the ceiling grid with the "T" Bars (9) running through the Bar

Hanger Notches (10). Using a flat head screwdriver or other tool, bend the integral t-bar mounting tabs (11)

downward to a vertical position (Fig. 3). Secure housing to the support structure with tie wire (supplied by

others) in the holes supplied. Sheetmetal screws (supplied by others) can also be used in the holes supplied

(20).

3. Locate Housing along Bar Hanger in desired position and, using pliers, squeeze the 4 Locking Tabs (12) on

the Plaster Frame (13) tightly over the Bar Hangers to prevent further Housing movement. Bar Hangers (6)

may be installed in alternate Slots (23) if mounting conditions require.

4. As desired, hanger bars (6) may be shortened at score mark to fit tight mounting conditions and joist

alignment tabs removed to adjust vertically as needed by breaking off with pliers.

5. Unsnap Junction Box Cover (14) by lifting the Leaf Spring (24).

. Run supply wires through UL Listed connectors (not supplied) in one of the five Pryouts (15) on the Junction

Box (16) or Type NM cable (ROMEX) through an Opening above the Wire Retaining Plate (17). Connect

Supply Wires (19) as shown in Fig 4 & 5. Replace Cover.

7. Select a Trim from the Wattage Label inside the Housing. Use Only Lamp Types approved for the Trim

chosen. DO NOT EXCEED MAXIMUM LISTED WATTAGE(S)!

INSTRUCTION SHEET MUST BE REMOVED FROM FIXTURE

PRIOR TO ENERGIZING.

1 2

Instruction 1
WIRING DIAGRAM 2

Summary of Contents

Page 1 - Instruction

InstructionSheetPart No....With representatives offices in principal cities throughout North America.Copyright

Page 2 - WIRING DIAGRAM

InstructionSheetPart No............With representatives offices in principal cities throughout North America.Copyright

Comments to this Manuals

No comments

Prescolite BX4-12 User Manual

Browse online or download User Manual for Lighting Prescolite BX4-12. Prescolite BX4-12 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Prescolite BX4-12