Prescolite HV HID CYLINDERS User Manual download pdf

InstructionSheet

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .05296800

InstructionSheet

INSTALLATION INSTRUCTIONS

HC/HD/HV HID CYLINDERS

. SURFACE MOUNT

. Secure mounting channel assembly to a 3 1/2"or 4" octagonal box

(Fig. 1). End slots in channel are provided for additional security, and

additional bolts through these slots are recommended for applications

here winds, vibration, or earthquakes may be encountered. Make

electrical connections in outlet box.

2. (HV cylinder only) Loosen both socket bracket mounting screws and

swing socket bracket toward capacitor bracket (Fig. 2b).

3. F

eed channel assembly leads into luminaire top assembly. Engage

unning thread and rotate assembly a few times. Make sure leads are

hanging freely on one side of the lamp socket bracket (Fig. 2). Rotate

assembly until canopy contacts ceiling.

a. (HC/HD cylinder) Assembly may be locked to running thread by

tightening the set screw (Fig. 2a).

b. (HV cylinder) Pull engaged end of socket bracket down slightly ans

swing bracket past mounting screw toward ballast. Tighten thread

clamp screw to running thread. Return socket bracket to original

position and tighten screws (Fig. 2b).

4. Make electrical connections inside fixture. Splice ground wire to fixture

ground wire, splice white supply lead to white fixture lead labeled

‘com’, splice black supply lead to black fixture lead labeled ‘line’.

B. PENDANT MOUNT

1. Secure pendant mount assembly to 3 1/2", or 4" octagonal box (Fig.

3). End slots in casting are provided for additional security, and

additional bolts through these slots are recommended for applications

where winds, vibration, or earthquakes may be encountered. Make

electrical connections in outlet box.

2. With HV cylinders, loosen both socket bracket mounting screws and

swing socket bracket toward capacitor bracket (Fig. 2b).

3. Rest canopy on luminaire top assembly. Feed pendant assembly 4"

into luminaire top assembly

. Engage pendant thread and rotate

assembly a few times. Make sure leads are hanging freely on one

side of the lamp socket bracket (Fig. 3). Rotate assembly until

pendant threads are fully engaged.

a. (HC/HD cylinder) Assembly may be locked to running thread by

tightening the set screw (Fig. 3a).

b. (HV cylinder) Pull engaged end of socket bracket down slightly ans

swing bracket past mounting screw toward ballast. Tighten thread

clamp screw to running thread. Return socket bracket to original

position and tighten screws (Fig. 3b).

4. Make electrical connections in fixture. Splice ground wire to fixture

ground wire, splice white supply lead to white fixture lead labeled

‘com’, splice black supply lead to black fixture lead labeled ‘line’. (see

Fig. 3). Replace housing and reflector and install proper lamp (Fig. 4).

5. If luminaire is not hanging straight, loosen the four ball clamp screws

in pendant casting (see Fig. 3).

Align luminaire and retighten screws.

6. Install canopy.

7. If installed in windy areas, or in areas subject to vibration or

earthquakes, a safety chain or cable is recommended (by others).

Fig. 1

Rotate

Canopy

Mounting Channel

Channel Assembly Leads

Fig. 2a

Fig. 2b

Fig. 2

Channel

Assembly

Leads

Luminaire Top

Assembly

Capacitor

Bracket

Thread

Clamp

Socket

Bracket

Set Screw

OTE: For surface and pendant mounting configurations first remove reflector by loosening two retaining screws.

Rotate reflector to disengage and remove, then remove housing cylinder.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

701 Millennium Boulevard • Greenville, SC 29607

With representatives of

fices in principal cities throughout North

America.

1 2

InstructionSheet 1

Summary of Contents

Page 1 - InstructionSheet

InstructionSheetwww.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ETPart No. . . . . . . . . . . . . . . .

Page 2

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ETPart No. . . . . . . . . . . . . . . . . . . . . . . .

Comments to this Manuals

No comments

Prescolite HV HID CYLINDERS User Manual

Browse online or download User Manual for Lighting Prescolite HV HID CYLINDERS. Prescolite HV HID CYLINDERS User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Prescolite HV HID CYLINDERS