InstructionSheet
www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET
101 Corporate Drive • Spartanburg, SC 29303
With representatives of
fices in principal cities throughout North
America.
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .03424400
InstructionSheet
INSTALLATION INSTRUCTIONS
37CF-1 and 4
1. Install the housing by nailing the mounting brackets on the
housing to the frame support as shown in Fig. 1, or frame in
the housing as desired for wet or dry wall construction.
2. Assemble the gasket and trim ring to the housing with (4) 6-32
x 1/4 flat head screws (provided in packet) as shown in Fig. 3.
Adjust the mounting brackets to locate the housing as required
for flush or profile trim (Fig. 2).
3. Install the conduit (by others) to align with the 1/2-14 NPT
tapped holes in housing as shown in Fig. 2. For through
wiring: align with hole to be used in J-Box (Fig. 4). Remove the
4 screws retaining the socket mounting plate and lift out plate.
For through wiring: remove the J-Box cover (Fig. 4).
4. When installed in concrete pour or mortar and in a situation
where direct water exposure is frequent, the concrete or mor
-
tar is to be suitably treated with a sealing or repelling agent
to insure that the fixture housing does not retain continuously
wet.
5. Make electrical connections. Connect ground wires to green
ground leads. Connect white (common) to white leads.
Connect power supply (line) to black leads. (see wiring
diagram)
W
ARNING: DO NOT pinch wires. Consult a Qualified
Electrician for all other options that require other wiring
configurations.
For through wiring: replace the J-Box cover
(Fig. 4). Replace the socket mounting plate and install lamp.
Support Frame
(By Others)
Housing Installation
Figure 1
Conduit
(By Others)
Housing
Ground Screw
IMPORTANT: When installed in brick or brick veneered
walls, the recessed portion of the housing must be coated
with asphaltum or similar protective material. Some types
of bricks retain moisture and other substances that can
damage the housing. Do not clean brick wall with acids
while fixture is in place.
Profile or Flush Trim
Figure 2
Adjustable Mounting
Bracket (2)
Fastener (Nail)
(By Others)
Flush Trim
(Wet Construction)
Adjustable
Mounting
Bracket (2)
Conduit
Entry
Profile Trim
(Wet or Drywall
Construction)
Housing
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker.
All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals