Prescolite D4LED User Manual download pdf

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ET

InstructionSheet

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93006637

InstructionSheet

INSTALLATION INSTRUCTIONS

D4LED AND D6LED SERIES

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER

OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

1. Bend brackets as shown in FIG. 1. Install the fix-

ture in the ceiling using mounting channels or bar

hangers (B6, B24, or by others) placed in the

adjustable mounting brackets. Mount the fixture

in the ceiling so that the weight of the fixture is

supported by the mounting channel or

bar and/or hanger wires secured to the building

structure (not ceiling).

2. Adjust the fixture so the bottom edge of the plas-

ter flange opening is flush with the finished ceil-

ing line and in alignment with adjacent fixtures.

Secure mounting brackets by tightening wing nuts

on either side of the fixture.

3. Remove J-Box cover. Remove appropriate knock-

out and install appropriate UL listed conduit con-

nector for the supply wire used. Connect white

fixture wire to white (common) supply wire, con-

nect fixture ground wire to green (ground) wire,

connect black fixture wire to black (line) supply

wire using UL listed wire connectors. Reinstall

J-Box cover.

WARNING: DO NOT pinch wires

between J-Box/ballast cover and J-Box.

Consult a Qualified Electrician for all

other options that require other wiring

configurations.

4. After all ceiling installation and finishing work

is complete, attach the safety cable to the light

engine/reflector assembly, by unscrewing the

wing nut (FIG. 2).

5. Connect the wires coming from the light engine

to the wires coming from the driver conduit by

snapping the two connectors together (FIG. 3

FIG. 4)

6. Install driver conduit connector into 7/8” hole in

light engine reflector on splice box. Caution: Do

not pinch wires

7. Insert the light engine/reflector assembly into

the opening of the housing. Pay attention to the

hexagonal rod that needs to slide into the heat

sink hole. Tighten the captive tamper proof screw

using the insert bit provided. Make sure the

reflector is flush against the ceiling.

NOTE: During step 7 use gloves to pre-

vent fingerprints on the reflector and

trim.

Wing Nut

NOTE: Adjustable mounting

brackets are supplied flat. To

ensure proper alignment, bend

brackets in line with marks on

flange as shown in FIG. 1.

FIG. 1

FIG. 2

Bend Brackets

in Line with

Marks on

Flange.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions con-

cerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in

areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or

circuit breaker. All installation servicing or relamping must be performed by qualified service personnel. Product must

be grounded to avoid potential electric shock or other potential hazard. Product must be mounted in locations and

at heights and in a manner consistent with its intended use, and in compliance with the National Electrical Code

and local codes. The use of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause

an unsafe condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items

such as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may cause an

unsafe condition.

Hex Nut

Safety Cable

Wing Nut

Screw

Reflector

NOTE: B26 and B24 Bar Hanger must

be ordered separately.

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Safety Cable

Driver Conduit

Connector

LED Light Engine/

Reﬂector Assembly

J-Box

Cover Plate

FIG 3

D6LED Series

Safety Cable

Driver Conduit

Connector

LED Light Engine/

Reﬂector Assembly

J-Box

Cover Plate

FIG 4

D4LED Series

Hexagonal Rod

Hexagonal

Rod

Driver Connector

Light Engine

Connector

Driver Connector

Light Engine

Connector

Safety Cable

Driver Conduit

Connector

LED Light Engine/

Reﬂector Assembly

J-Box

Cover Plate

FIG 3

D6LED Series

Safety Cable

Driver Conduit

Connector

LED Light Engine/

Reﬂector Assembly

J-Box

Cover Plate

FIG 4

D4LED Series

Hexagonal Rod

Hexagonal

Rod

Driver Connector

Light Engine

Connector

Driver Connector

Light Engine

Connector

WARNING- This product contains chemicals known to the State of California to cause cancer, birth defects and/or

other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this

product.

FIG. 1

Bend Brackets in

Line with Marks

on Flange

FIG. 3

D6LED Series

FIG. 1

FIG. 2

FIG. 4

D4LED Series

InstructionSheet 1

Summary of Contents

Page 1 - InstructionSheet

www.prescolite.com • Prescolite TollFree Technical Support 1.888.PRS.4TEC • Hours: 8am - 5pm ETInstructionSheetPart No. . . . . . . . . . .

Related models: D6LED

Comments to this Manuals

No comments

Prescolite D4LED User Manual

Browse online or download User Manual for Lighting Prescolite D4LED. Prescolite D4LED User Manual

Summary of Contents

Related models: D6LED

Comments to this Manuals

Related products and manuals for Lighting Prescolite D4LED